Index
All guides
Every guide, code, chart and tool on mechy.si. Can't find yours? Snap it and Mechy makes one.
Nothing here matches. Snap it and Mechy makes a guide for it.
Home and outdoor repairs 10
Fault codes 66
- Fault codes
- Bobcat fault codes
- Kubota fault codes
- 14-03: Fuel shutoff pull solenoid error OFF (older code)
- D3907: Left joystick Y-axis not in neutral
- D7501: Drive CAN joystick information error
- D7527: Drive left swash plate out of position
- DR-2: Drive response setting (not a fault)
- E-93: Starter relay trouble
- E000097-03: Water in fuel sensor fault
- E000097-31: Water in fuel detected
- E000157-21: Rail pressure control fault
- E001076-16: Rail pressure control fault
- E005324-04: Glow plug signal fault
- E9000: DPF regeneration needed (engine rpm too low)
- E9006: DPF regeneration blocked by inhibit switch
- E9120: Fuel filter water warning
- E9302: Engine fuel system leakage
- E9310: Starter turn-on limited
- E9400: Other failures
- H1224: Right thumb switch not in neutral
- H2607: Front auxiliary base solenoid open circuit
- H2907: High-flow solenoid open circuit
- H3916: Left joystick no communication
- H7404: Main controller no communication
- L0402: Information button error ON
- L7404: Main controller no communication
- M0116: Air filter sensor not connected
- M0117: Air filter plugged
- M0217: Hydraulic/hydrostatic filter plugged
- M0309: System voltage too low
- M0509: Hydraulic charge pressure too low
- M0514: Hydraulic charge pressure extremely low
- M0515: Hydraulic charge pressure shutdown
- M0710: Hydraulic fluid temperature too high
- M0810: Engine coolant temperature too high
- M0909: Fuel level too low
- M0921: Fuel level sensor out of range high
- M1210: Intake air temperature too high
- M1607: Traction lock solenoid open circuit
- M1706: Hydraulic lock valve short to ground
- M1732: Hydraulic lock valve overcurrent
- M2302: Starter relay error ON
- M2303: Starter relay error OFF
- M2899: Throttle secondary sensor not calibrated
- M3204: ACS controller no communication
- M3507: Hydraulic fan open circuit
- M4404: Auxiliary controller no communication
- M4803: Front light relay error OFF
- M5107: Rear light output open circuit
- M5306: Press to Operate light short to ground
- M5810: Fuel temperature too high
- M6302: Tailgate fan 2 error ON
- M6604: ECU no communication
- M6803: HVAC relay error OFF
- M7748: Key switch multiple
- M7974: Door open
- P0093: Fuel leak in high-pressure system
- P0336: Crankshaft position sensor abnormality
- P0563: Battery voltage too high
- P0606: ECU processor or memory fault
- W3234: ACS tilt actuator not in neutral
- W3236: ACS lift actuator fault
- W3276: ACS CAN joystick information error
- W4005: Right joystick X-axis not in neutral
- W4007: Right joystick Y-axis not in neutral
Size charts 6
What size do I need? 9
- What size do I need?
- Drill Bit Size for a 1/4-20 Tap (and How to Tap It)
- Drill Bit Size for a 10-32 Tap (Plus 10-24 and 8-32)
- Grease Zerk Thread Size: How to Tell Which You Have
- Lug Nut Torque Specs: Find Yours and Torque It Right
- What Size Bolt Do I Need? (Measure It or Snap It)
- What Size Screw for 1/2 in Drywall?
- What Size Screws for a Door Hinge?
- What Size Screws for a License Plate?